Looking for High-Performance Plastic Components?
Nylon 6/6 is the extrusion grade of the Nylon family of solid polymer shapes. It has been commercially available since 1948; developed by Dupont. Nylon is well known for excellent toughness, low coefficient of friction and good abrasion resistance making it an ideal replacement for a wide variety of materials from metal to rubber. Using Nylon 6/6 reduces lubrication requirements, eliminates galling, and corrosion. Low cost combined with improved wear resistance makes Nylon 6/6 an excellent choice for many bearing and wear components.
Nylon 6/6 is easily fabricated into precision parts using standard metalworking equipment. Tolerances of +/-.002 are easily achieved with experience. It is available in a broad variety of shapes and sizes. Rod stock normally comes ground to size making turning easier. Both extruded and cast grades of nylon are available with a variety of fillers to meet specific application demands.
Several manufacturers offer varying grades and filled versions thereof by the names of Tecamid® and Nylatron®, commercially available to accommodate specific applications. Solid lubricants such as mineral oil, , graphite, PTFE, and MoS2 provide lower friction, while reinforcing agent such as carbon fiber, Kevlar®, and glass provide higher levels of strength and dimensional stability.
| Specification | Test | Value | Units |
| Specific Gravity, 73°F | D792 | 1.15 | - |
| Tensile Strength @ Yield, 73°F | D638 | 12,000 | psi |
| Tensile Modulus of Elasticity, 73°F | D638 | 425,000 | psi |
| Tensile Elongation (at break), 73°F | D638 | 50 | % |
| Flexural Strength, 73°F | D790 | 15,000 | psi |
| Flexural Modulus of Elasticity | D790 | 450,000 | psi |
| Shear Strength, 73°F | D732 | 10,000 | psi |
| Compressive Strength - Ultimate | 300 | psi | |
| Compressive Strength at 2% Deformation | D695 | 300 | psi |
| Compressive Strength at 10% Deformation | D695 | 8,000 | psi |
| Deformation Under Load | % | ||
| Compressive Modulus of Elasticity, 73°F | D695 | 420,000 | |
| Compressive Strength ⊥ to Laminate (Modulus) | psi | ||
| Compressive Strength ⊥ to Laminate (Yield) | 1,000 | psi | |
| Compressive Strength ⊥ to Laminate (Ultimate) | 1,000 | psi | |
| Hardness, Durometer (Shore "D" scale) | D2240 | D80 | |
| Hardness, Rockwell (Scale as noted) | D785 | 115 | Rockwell R |
| Izod Impact, Notched @ 73°F | D256 Type A | 0.6 | ft.lbs/in. of notch |
| Coefficient of Friction (Dry vs Steel) Static | PTM55007 | 0.3 | |
| Coefficient of Friction (Dry vs Steel) Dynamic | PTM55007 | 0.25 | |
| Maximum Static Bearing Load (P) | PTM55007 | 300 | psi |
| Maximum Unlubricated No Load Bearing Velocity (V) | PTM55007 | 60 | ft/minute |
| Maximum Limiting PV (Unlubricated) | PTM55007 | 2,700 | psi x ft/min. |
| Wear Factor "K" x 10-10 | PTM55010 | 80 | Cubic in.-min/ft.lbs.hr |
| Sand Wheel Wear/Abrasion Test | 75 | UHMW=100 | |
| Minimum Mating Surface Hardness | 20 | Rockwell (Brinnell) | |
| Coefficient of Linear Thermal Expansion | E-831(TMA) | 5.50 | in/in/°F x 10-5 |
| Coefficient of Thermal Expansion // to Laminates | E-831(TMA) | 5.50 | in/in/°F x 10-5 |
| Coefficient of Thermal Expansion I to Laminates | E-831(TMA) | 5.50 | in/in/°F x 10-5 |
| Softening Point | 200 | °F | |
| Heat Deflection Temperature 264 psi | D648 | 200 | °F |
| Embrittlement Temperature | °F Min. | ||
| Continuous Service Temperature in Air | 210 | °F Max. | |
| Short Term Service Temperature | 210 | °F Max. | |
| Tg-Glass Transition (Amorphous) | D3418 | °F | |
| Melting Point (Crystalline) Peak | D3418 | 500 | °F |
| Thermal Conductivity | F433 | 1.7 | BTU-in/(hr/ft2°F) |
| Dielectric Strength Short Term | D149 | 400 | Volts/mil |
| Surface Resistivity | D257 | >1013 | ohm/cm |
| Volume Resistivity | D257 | ohm/cm | |
| Dielectric Constant, 106 Hz | D150 | 3.6 | |
| Dissipation Factor, 106 Hz | D150 | 0.02 | |
| Flammability @ 3.1mm(1/8 in.) UL94 | UL94 | V-2 | |
| Arc Resistance | seconds | ||
| Water Absorption, Immersion 24 Hours | D570 (2) | 0.3 | % |
| Water Absorption, Immersion Saturation | D570 (2) | 7.0 | % |
| Machinability Rating | 2 | 1=easy, 10=difficult | |
| Rod Diameter Availability (Off the Shelf) | .25 | 6.0 | inches |
| Sheet Thickness Availability (Off the Shelf) | .125 | 3.0 | inches |